埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3086|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑 : s! p1 i* A0 e# `
7 ?/ j- o0 j6 r4 V" S$ Z0 y
Two  cutler –hammer advantage  starters are  doing the same thing:8 |9 q  x; l5 C& n8 ]5 ^
After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again.
9 @  ]1 Q% U0 T! ZIt is a cycle.4 D7 l9 T+ a( R/ q
2 a# N( I/ ~8 Y$ u
We isolate the network control and use the local start and stop only, the problem remains.
7 I0 Y, G; y9 ^, O7 TSwap one of the defective buckets with a good one, the new bucket works fine.
7 ^) K1 j4 `3 D0 R! j/ H/ `The problem should be inside the bucket.
4 k3 B8 U' H; R
, X5 S4 c7 Y8 @" S8 J  qWhen the problem happened, we observed that  the contactor has a pulling action but will not seal.: u6 W7 {' O* m& N3 E7 q8 }
Use a terminating screw divers to push in the contactor, it will not seal either.
. v) Q7 Z/ c: U( Q$ T: @6 RConfirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same./ X/ y5 |& R; d. v. m
0 L: ^/ i1 S) S( M) T) |7 S
The next thing we can think of  is the coil, we took the coil out to have a close look.
2 c8 e& X% O- k, e2 U% U& xThey  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.
1 w6 |7 A% K# e* F& ?6 n; H- u% B! z It is getting better  this time, we have 7-8 times of running before it quit working.
9 x, j6 d9 a; ^
6 O% p/ U9 |% Y+ m- I9 PThe coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them. 0 `/ p# u1 ?" T  h
5 m  R) r- m8 J2 Q- \& V7 g: T, D
Do you guys have any input on this issue?
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
大型搬家
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑 - M5 j4 F. t! j

1 \& h" p& E8 \& w% t& p. b1 v中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection.: ~1 O( j8 E  r- k
Since your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
大型搬家
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行 9 B! z; }' l: }3 j; \4 z# r
也想到这一点,不过这是新装的设备。
' }- F0 u+ l3 x+ F) j+ E$ T9 h: ?检查过触点没问题。
大型搬家
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-18 09:40 , Processed in 0.595888 second(s), 16 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表