 鲜花( 0)  鸡蛋( 0)
|

楼主 |
发表于 2010-7-10 17:18
|
显示全部楼层
本帖最后由 jack_lai 于 2010-7-10 18:52 编辑 ' m( l. O, _( W9 C' s1 [
0 ]- P/ x3 j' V: W$ F3 a8 `3 {
1# jack_lai
, R, Z3 T7 O# Z" L, c
- V. `/ }, V0 Z- J4 U; A足球看完了来看看题目。8 V, j/ j+ o4 i4 l$ v
0 |- A! g$ \/ E( `; G2 \The length of the heat trace is 22 meters. The size of the heat trace is 5/16 inch (WATTS/ m SUPPLIIED is 43.7)
& O: L9 v3 t" R: B; {The drawing is shown as figure 1. (All data is from the memory. They are not the same as the real drawing, but a little bit different)
* F0 C7 t/ M3 I3 B5 M z" mWe can see it is not easy to install the 22 meters heat trace according as figure 1
- l; n4 c. m7 m1 p/ w
" C1 N4 ~: S+ Y- q
6 `$ X; Y7 H7 R- T. i
- |6 r M. h: }8 x
$ w7 p7 `( Z1 k+ t- |3 |As a normal question we just discuss:0 X, k; k' E# } Z8 h
How do you run these 9.4 meters heat trace (size 5/16 inch) on the 3 inches 1.4 meters pipe ? - y* q8 y$ i: n! H
I call this is JACK LAI Spiral Method 螺旋法
; S3 J6 \3 u& S3 K6 |' QThe outside circumference of the 3 inch pipe is more than 10 inches. See figure 2.
1 o! W, P7 @6 t6 oThere are 10 positions to plac the heat trace. They are 0.1,2,3,,,,,9. The distance between each position--heat trace is about one inch. 3 F8 m, u: F% h4 T" r* \+ y
Because the pipe is horizontal, position 0 can not be placed. See figure 2 C1 m: E% }7 Q/ l
Because the maximum bend radius of the heat trace is 2 inches( see note 1), position 5 can not be placed. See figure 2. Then the route of the heat trace can be like figure 3
: O+ q( Z9 P8 |! A2 O+ xThe total heat trace that can be installed here is about 8 L5 }- h0 t( b# ~# l; N
1.4 * 6 + 1 * 2 = 8.6 + 2 =10.8 Meters1 ] W5 T h! G& t" X- U
So, the 9.4 meters heat trace can be installed along the 3 inched 1.4 meters pipe without a problem.
% M2 r& {9 b4 y! h" L* M; w/ G" a( s7 @; Q' g
Note :
& Z/ p+ J' K/ r6 a( l7 D" b1. The minimum bend radius:! b( {% D3 M. O4 z, x( l
Because the heat trace size here is 5/16, 6 times the outside diameter of the heat trace is
1 W9 Q8 n2 g E) c. s5/16 *6 = 30/16 almost = 2 inches( ~# M3 j! t4 ]; m: O% m) n
So the maximum bend radius is 2 inches.
. l E8 d: M6 l5 F8 a8 f; }7 N% i1 x- Q0 |
/ P3 Y' R/ l; r. [4 p7 P
7 G* O! T- b/ Q2 A p$ s
Summary" s+ Z, d ~: h2 o, X8 P, _
As regular # |# n6 |4 N' f) T% t
For 3 inch pip: If heat trace size is 5/16 inch, and no RTD, the box position is close to the end of pipe. 1 meter long pipe
0 N. `9 p2 `% mif the pipe is horizontal, The length of heat trace can be installed is about9 Z6 j4 M2 H9 a+ s
1 * 9 = 9 meters
0 `. x) H; c ~. S8 `If the pipe is vertical, The length of heat trace can be installed is about, G, f P' c/ x) U
1 * 10 = 10 meters.
/ w9 z/ \4 j kFor 2 inch pipe: If heat trace size is 5/16 inch, and no RTD, the box position is close to the end of pipe. 1 meter long pipe$ w& H- f, h8 u/ p+ G
if the pipe is horizontal , The length of heat trace can be installed is about# V4 W7 r7 A! [- B9 R, N5 g8 n7 L
1 * 4 = 4 meters
7 Q# S, i- r9 a0 a# ^6 d$ x! DIf the pipe is vertical, The length of heat trace can be installed is about
( m- H0 o/ ]' t( T; b1 * 5 = 5 meters. |
|