埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3087|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑
9 \. J3 f- w1 m8 f' B0 g
% j0 g8 E/ c2 p, C' h2 ?Two  cutler –hammer advantage  starters are  doing the same thing:+ e: \& C( D( O# @. o  Q
After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again. 0 j: n2 m; D# d  t/ C$ b4 [3 \
It is a cycle.% L( \( D3 ^5 B/ J; e; z; R
6 L# V+ n# Y; |. F) n, u& M
We isolate the network control and use the local start and stop only, the problem remains.
6 ^6 m4 u2 ?( x! ~+ z, |Swap one of the defective buckets with a good one, the new bucket works fine.+ F1 ~9 ?9 B# a+ Q( V; E
The problem should be inside the bucket.
, {- k8 H4 d- x( d
$ r! |" N* A% ]0 [When the problem happened, we observed that  the contactor has a pulling action but will not seal.! b& y$ P! u) I4 v+ P( h
Use a terminating screw divers to push in the contactor, it will not seal either.
7 q' e. B3 m3 H: W! e; LConfirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same.9 n  [+ o* l" z( a* ?9 A8 Q$ e
4 K5 @  W- Y: ~9 {" k
The next thing we can think of  is the coil, we took the coil out to have a close look.( D9 _- d" I' l9 _* `0 p, x
They  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.
  A! r4 e  k# _( k7 j It is getting better  this time, we have 7-8 times of running before it quit working.
/ ?1 x* S. E( ^
/ E6 E# |* i. }$ Y# @The coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them.
! z( w, c% |7 e# ]! q: j1 k0 Y. z, J6 a6 z$ W
Do you guys have any input on this issue?
大型搬家
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
大型搬家
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑 9 M; A( I1 V! n- N

, g) `4 @# B" G; ]8 `5 v4 F中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
大型搬家
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection.
( G( f7 D$ S$ h; [: PSince your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行 - J3 ^; a$ s7 E. S2 P$ Q4 f1 a
也想到这一点,不过这是新装的设备。1 c& W- c) _+ t2 f- L' ]; B& O& n
检查过触点没问题。
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-18 09:46 , Processed in 2.360452 second(s), 16 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表