 鲜花( 0)  鸡蛋( 0)
|

楼主 |
发表于 2010-7-10 17:18
|
显示全部楼层
本帖最后由 jack_lai 于 2010-7-10 18:52 编辑 : \9 S2 x# j P( q) n5 p
9 T2 c0 [% M$ b% ^2 t
1# jack_lai
% }- k0 b+ b' I9 y$ j
& F1 Z6 g& e+ A; ^- g z9 `3 ?# i足球看完了来看看题目。3 b4 D; x9 }( ?+ y) c
: P2 r7 f) c& o8 o! R3 p2 n4 l4 H
The length of the heat trace is 22 meters. The size of the heat trace is 5/16 inch (WATTS/ m SUPPLIIED is 43.7)
7 p' i% U& O8 m2 x! Z, Y O. fThe drawing is shown as figure 1. (All data is from the memory. They are not the same as the real drawing, but a little bit different)0 _4 n/ H& |3 @- L* l- A, U
We can see it is not easy to install the 22 meters heat trace according as figure 11 n# P5 Q& ~: D* f X
5 ^' I4 X7 \- Y7 D6 S
/ a) s: p6 I2 P& r9 j0 F
5 u# o5 ]) b! W8 \$ f" ]) x D4 g ]& S! N- V6 ~4 k" X0 u+ g
As a normal question we just discuss:2 @% ^. a# ~# F/ j2 C% ?# W
How do you run these 9.4 meters heat trace (size 5/16 inch) on the 3 inches 1.4 meters pipe ?
* H5 H+ r/ y3 S, XI call this is JACK LAI Spiral Method 螺旋法
% A9 X5 D* c0 y, GThe outside circumference of the 3 inch pipe is more than 10 inches. See figure 2.
& m$ a3 N" |6 |$ sThere are 10 positions to plac the heat trace. They are 0.1,2,3,,,,,9. The distance between each position--heat trace is about one inch.
9 Y. E1 f# x2 Q( E- a/ X u7 ?Because the pipe is horizontal, position 0 can not be placed. See figure 2% t# W2 \* H) n7 o
Because the maximum bend radius of the heat trace is 2 inches( see note 1), position 5 can not be placed. See figure 2. Then the route of the heat trace can be like figure 37 ? ^2 v4 _6 V+ a9 l% C3 W3 _
The total heat trace that can be installed here is about
) d# \9 O% V5 ~+ i# F1.4 * 6 + 1 * 2 = 8.6 + 2 =10.8 Meters
1 b. [ E* R& `+ s6 oSo, the 9.4 meters heat trace can be installed along the 3 inched 1.4 meters pipe without a problem.
$ b5 f) @- ?" F, N& F( Y' s
, H T( `! g& l9 F# ENote :
) H' E: I( J( X/ R$ ~1. The minimum bend radius:& O. J0 _% q* l4 c8 _& q9 q- N
Because the heat trace size here is 5/16, 6 times the outside diameter of the heat trace is
& C9 U- r1 M8 ~+ q) X5 \! K5/16 *6 = 30/16 almost = 2 inches: Z4 ~* ^6 P r, p; a1 ~# {2 X+ b. s
So the maximum bend radius is 2 inches.; r; S9 i) T: `5 x
5 Q( c; H# l2 L
8 X' L" }; O( x k
; G( c; u, C# _& [' F6 d
Summary7 {: _) ~3 h. V; m0 h
As regular 2 E0 {# c5 ?2 c2 D* W
For 3 inch pip: If heat trace size is 5/16 inch, and no RTD, the box position is close to the end of pipe. 1 meter long pipe
' X3 j; L: G. R( N; Y) iif the pipe is horizontal, The length of heat trace can be installed is about
+ c* p+ Y- _3 f1 * 9 = 9 meters
# ~% }0 |. H' I$ f% B- b( XIf the pipe is vertical, The length of heat trace can be installed is about, C( Z( L+ t* M% a/ S
1 * 10 = 10 meters. # \1 q. W. {( T( q/ j
For 2 inch pipe: If heat trace size is 5/16 inch, and no RTD, the box position is close to the end of pipe. 1 meter long pipe
- a, [6 N& V# [if the pipe is horizontal , The length of heat trace can be installed is about
- j) J- U. q, V1 * 4 = 4 meters
1 C' v$ X( Q% j# v& Q8 zIf the pipe is vertical, The length of heat trace can be installed is about
7 V8 i2 L7 p# ~( S8 h/ m3 Z1 * 5 = 5 meters. |
|