 鲜花( 0)  鸡蛋( 0)
|

楼主 |
发表于 2010-7-10 17:18
|
显示全部楼层
本帖最后由 jack_lai 于 2010-7-10 18:52 编辑
1 v! e6 E5 E4 f9 {. _2 ]) Z0 R+ R4 e
1# jack_lai ' E" V; B- l" C# E* J
* s% N3 O( J: X6 N/ U& V足球看完了来看看题目。) z9 i5 h( P" @
& ^% ]) ?" L. [5 i8 x `1 x) V- uThe length of the heat trace is 22 meters. The size of the heat trace is 5/16 inch (WATTS/ m SUPPLIIED is 43.7)
; m/ D4 q8 _' w. ]6 b/ F- ]2 FThe drawing is shown as figure 1. (All data is from the memory. They are not the same as the real drawing, but a little bit different)
( M8 V& D5 r3 lWe can see it is not easy to install the 22 meters heat trace according as figure 1
* H" j# P6 X( ?' v; k4 [
* ]9 c5 C" b( X9 p
- Z: U( Y# d+ [0 t/ ~1 g0 }
; `& p/ x1 u6 H% q/ v+ b4 L. j( ]) b- h# M
As a normal question we just discuss:4 Q, t* J) w6 M3 M! d7 G
How do you run these 9.4 meters heat trace (size 5/16 inch) on the 3 inches 1.4 meters pipe ?
2 V# d4 _! {" x9 A3 \7 aI call this is JACK LAI Spiral Method 螺旋法& y$ s+ @7 u. j5 F
The outside circumference of the 3 inch pipe is more than 10 inches. See figure 2.
% k9 S& u5 u0 y+ jThere are 10 positions to plac the heat trace. They are 0.1,2,3,,,,,9. The distance between each position--heat trace is about one inch.
2 q( k4 S" ^! F, OBecause the pipe is horizontal, position 0 can not be placed. See figure 2$ H( Z# [# Q/ f1 T9 X1 Q2 u
Because the maximum bend radius of the heat trace is 2 inches( see note 1), position 5 can not be placed. See figure 2. Then the route of the heat trace can be like figure 3- o8 L" W- i" C2 `+ ?
The total heat trace that can be installed here is about
, \, O" D4 H; A1 K0 r' ?" p1.4 * 6 + 1 * 2 = 8.6 + 2 =10.8 Meters# w; K; O# @) l' V% K* s
So, the 9.4 meters heat trace can be installed along the 3 inched 1.4 meters pipe without a problem.
4 _9 T1 a6 _% t# L0 C, C) G4 j7 q5 o) m) p1 h" k) A- Z
Note :2 j/ }# Q/ O1 h2 z# E) Q- o
1. The minimum bend radius:' |" `+ C3 D* X& S' K
Because the heat trace size here is 5/16, 6 times the outside diameter of the heat trace is! c- W0 w' {& N2 B
5/16 *6 = 30/16 almost = 2 inches
" {4 e9 e4 l" x- jSo the maximum bend radius is 2 inches.
7 {! v8 h0 m4 u3 `0 \
. H Y0 k% H) g7 ~
2 w4 e& P3 M4 f5 w8 _$ i7 v
a+ o1 } J( _+ M( ?Summary
K+ l% k1 g5 G$ `0 RAs regular
% L3 c J% s! N1 m) D7 m: v; R$ hFor 3 inch pip: If heat trace size is 5/16 inch, and no RTD, the box position is close to the end of pipe. 1 meter long pipe& L; I! t/ D, F- ^9 j8 ]+ I! j
if the pipe is horizontal, The length of heat trace can be installed is about
; c. J- ]7 o) { g' o4 \3 e5 x1 * 9 = 9 meters
/ S7 p9 i( L X/ tIf the pipe is vertical, The length of heat trace can be installed is about0 ~1 \5 f$ `( t2 l. f9 T
1 * 10 = 10 meters. & B% j+ c# E( N! o
For 2 inch pipe: If heat trace size is 5/16 inch, and no RTD, the box position is close to the end of pipe. 1 meter long pipe( b% J4 l* T6 l9 |
if the pipe is horizontal , The length of heat trace can be installed is about
1 P, T; L: I. j" Q1 * 4 = 4 meters
. [5 W* S4 r+ S* S DIf the pipe is vertical, The length of heat trace can be installed is about9 H3 w( x# T0 [" M! e4 l. y
1 * 5 = 5 meters. |
|