埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3084|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑
. P9 l  r! D) B
' [. F" {0 @7 u, j) B, K) YTwo  cutler –hammer advantage  starters are  doing the same thing:9 y; j; x' k3 I+ g- g/ S4 ?+ C
After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again.
0 n3 ^" |/ V5 n1 X: qIt is a cycle.
, G5 z( }2 B! g  o) q1 \- @  }( D8 G2 ]
We isolate the network control and use the local start and stop only, the problem remains.
" k& W  [4 M5 a( Z  |Swap one of the defective buckets with a good one, the new bucket works fine.
; T& @1 I/ B; g4 \8 ^7 s" FThe problem should be inside the bucket.
4 m, `8 }8 F# c: h  H# A. G; G3 Z7 W& W7 P: J$ C" p
When the problem happened, we observed that  the contactor has a pulling action but will not seal.' ?2 H/ m" B! z# p% ~  ]# @
Use a terminating screw divers to push in the contactor, it will not seal either.
, V  v( V: M* n3 aConfirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same.
! J% C: k- t/ ~# H3 X3 n/ O( u+ D0 _" v5 r+ s0 r  M) r( p* K8 f
The next thing we can think of  is the coil, we took the coil out to have a close look.
) I  h" m1 H7 `" m. s! e* x# U! I3 L, \They  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.
' I3 \  i0 U" t; N. ^ It is getting better  this time, we have 7-8 times of running before it quit working. 6 ]- b- o3 H% B3 M
! L& f: S% `/ M, d/ w2 N  s
The coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them. ! w/ Q: M7 S! X' y

" w" ^* H- K; E  u0 {) A6 T2 ~Do you guys have any input on this issue?
大型搬家
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
大型搬家
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑
9 w5 I- h% G! J6 j( F& z5 I% L) M- P- M
中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection.; D9 p; Z: e' c7 g+ |& y) z
Since your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
大型搬家
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行
6 N3 X& u' A0 e) K也想到这一点,不过这是新装的设备。6 T# t% f6 ~+ G- }
检查过触点没问题。
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-18 09:27 , Processed in 0.189556 second(s), 16 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表